2009.10.24 v0.22
+ Two new mixing type 'ring' and 'cross'. You can change between mixing types with  the 'osc mod' panel. The first new does a ring modulation between the two occiloscope and the with 'osc 2 pitch ofs' slider you can alter the frequency of the second osciloscope based on the frequency of the first osciloscope. (Center means both are same). With 'cross' mixing you can cross fade between the two osciloscope. The 'osc balance' slider determines the fade factor (left = just osc1, right = just osc2). You can set the frequency of the second osciloscope with the 'osc 2 pitch ofs' slider similar like in the 'ring' mixing mode.
+ Second osciloscope has a new wave form. (organ)
! Tempo now is in bpm.
+ New continius test button ('tone'). With this you can hear the test sample continiusly and can set every parameters in real time except the adshr. (That works only with the impulse test button 'test')
! Sound stock generation is paused while the system generates the test sound. (after you change a parameter, or while the continius test sound is on)


Knowing bugs:

! When you start the program it will generate the initial sound samples for a few secounds. During this you can use everything, but if you play a tone under this, the sound will be distorted because the samples are not ready.
! During the sound sample generation the respone time is bit slower.
! The filter section is completly useless as that is not ready.
! ADSHR graph jitters if you try to incerase the size of the curve over 2sec.
! Graphics flickering everywhere
! 'sequenc' and 'volume' texts have different luminance. 
! If you play a test sound continiusly there is a possibility that the ds will not be able to calculate fast enought the sample and beacuse of that the sound will be distorted. With the actual buffer setting and math It should be ok, but I have to test it heavyly.
! Sometimes notes appear in random places if you touch the grid. ( in emu it is perferct :( )
! Some users say: It wont work on M3real with latest firmware. (try "noicon" version please)


2009.10.22 v0.21 initial release

+ 16x16 pattern editor (16 accord, 16 tone (Ionian), eleventh line is the A)
+ 16 different pattern stock 
+ different volume setting possibility for each accord (in the second editor mode)
+ adjustable tempo
+ possibilty to play a pattern looped with the default sound samples or with generated sound samples
+ with the button X you can clear a pattern (and set the volumes of that pattern to maximum)
+ Sound sample generator. You can listen a test sound or generate the full stock, that will be used by the pattern player. The system is fully usable while you play or generate samples. Although the playing of the pattern will be paused during the generation.
+ For the generation there are two osciloscopes. First can generate sinus, saw, rectangle and organ. The second can generate sinus, saw, rectangle or can be turned off. If the second is active that modulates the amplitude of the first osciloscope. The frekuency of the second osciloscope is adjustable from 0 hertz to 20 hertz.
+ you can set an ADSHR for the generated samples. The length of the samples are limited to 2 seconds.

Knowing bugs:

! When you start the program it will generate the initial sound samples for a few secounds. During this you can use everything, but if you play a tone under this, the sound will be distorted because the samples are not ready.
! During the sound sample generation the respone time is bit slower.
! If you generate the full sound sample stock and play a test sound the latter could be distorted, because there is not enough cpu to calculete both parallel. (I think I will simply pause the generation while the system plays the test sound)
! Osciloscope balance slider, Osciloscope mixing and the filter section are completly useless as there are not ready.
! ADSHR graph jitters if you try to incerase the size of the curve over 2sec.
! Graphics flickering everywhere
! 'sequenc' and 'volume' texts have different luminance.